Search

    Damp-proof course DELTA®-MAUERWERKSSPERRE (WALL BARRIER)

    Horizontal cross-section waterproofing in accordance with DIN 18533, permanently resistant and highly flexible.

    Due to the profiled surfaces, DELTA®-MAUERKSSPERRE achieves a high shear strength in the masonry (application type MSB-Q) by "clawing" into the masonry mortar.

    01 /01
    smallRetina 11:24:59 mediumAlias 11:24:59 large 11:24:59 xlarge 11:24:59
    DELTA®-MAUERWERKSSPERRE in der Anwendung
      smallRetina 11:24:59
      DELTA®-MAUERWERKSSPERRE in der Anwendung

    Advantages

    • High flexibility
      Even at low temperatures, the DELTA®-MAUERKSSPERRE remains very flexible: no risk of cold fractures, no tearing!
    • General building inspectorate test certificate
      The suitability of DELTA®-MAUERKSSPERRE as a horizontal cross-section seal is confirmed in AbP P-AB/13525/15-2013. Despite a material thickness of only approx. 0.4 mm, DELTA®-MAUERWERKSSPERRE meets the requirements for wall barriers according to DIN 18533-1! The track is light and flexible. In short: Easy to work with!
    • The lattice embossing on the top and bottom enables optimal "clawing" with the mortar and thus increases the shear strength in the masonry. DELTA®-MAUERWERKSSPERRE thus meets the requirements for damp-proof course of application type MSB-Q in accordance with DIN 18533 and can therefore be used in (cellar) exterior walls that are subjected to shear forces.
    • Rot proof
      DELTA®-MAUERWERKSSPERRE is resistant to the usual influences in the masonry/soil and is correspondingly permanently functional.
    • Easy to process
      Unroll DELTA®-MAUERWERKSSPERRE on the fresh mortar bed, align - and loosen the brickwork.

     

     

    Application

    DELTA®-MAUERWERKSSPERRE serves as a cross-section waterproofing in masonry in contact with the ground in accordance with DIN 18533, water exposure class W4-E.
    It is laid in one layer. The contact surfaces are to be leveled with masonry mortar thick enough to create a horizontal surface without unevenness. DELTA®-MAUERWERKSSPERRE is rolled into the fresh mortar. The membranes overlap by at least 20 cm (if the membrane overlaps are glued with DELTA®-THAN 5 cm is sufficient).
    The width of the strip should be selected so that no moisture bridges can form on either side of the bricked-up wall. In order to enable the waterproofing of a building to be professionally connected to the damp-proof course on the inside or outside, the damp-proof course should protrude at least 5 cm over the masonry.

    Technical data

    Material Polyolefin
    Colour black
    Surface rutschhemmend profiliert an Ober- und Unterseite
    Thickness approx. 0,4 mm
    Tear resistance (nail shaft) (EN 12310-1) Lengthways: approx. 130 N, Crosswise: ca. 160 N
    Resistance to folding at low temperatures (EN 495-5) -40 °C, kein Bruch, keine Risse
    Watertightness (EN 1928, Procedure B) bestanden (400 kPa/72 h)
    Reaction to fire (EN 13501-1) Brandklasse E
    Resistance bitumenbeständig
    Widths 11,5/12,5/15/17,5/20/24/25/30/36,5/42/50/60/100 cm
    Roll length 25 m
    Application type (DIN SPEC 20000-202) MSB-Q
    Water exposure class (DIN 18533) W4-E
    Room usage class (DIN 18533) RN1-E to RN3-E
    Crack class (DIN 18533) R1-E to R4-E

    Accessories

    smallRetina 11:24:59 mediumAlias 11:24:59
    DELTA®-THAN Anschluss am Kamin

    DELTA®-THAN

    Permanent elastic cartridge adhesive for outdoor use. Offers maximum security in the connection area.
    smallRetina 11:24:59 mediumAlias 11:24:59
    DELTA®-MWSP Clip in der Anwendung

    DELTA®-MWSP Clip

    Fastening clip for L-shaped barriers in double-skinned facing masonry.
    smallRetina 11:24:59 mediumAlias 11:24:59
    DELTA®-MAUERWEKSECKE Außenecke in der Anwendung

    DELTA®-MAUERWERKSECKE (Corner)

    Prefabricated inside and outside corners as a system supplement for all DELTA® damp-proof courses.

    Download

    PDF | 58.1 kB

    Technical data sheet DELTA®-MAUERWERKSSPERRE

    PDF | 162.6 kB

    Declaration of Performance DELTA®-MAUERWERKSSPERRE

    Contact

    smallRetina 11:25:00 mediumAlias 11:25:00 large 11:25:00 xlarge 11:25:00

    Would you like information on detailed product properties, use cases or other technical topics?
    Then feel free to contact our application department on +49 2330 63 578 or atabvf@doerken.de.

    Do you have questions about prices, availability or the status of your order?
    Our sales service will help you with these matters on +49 2330 63 636 or membranes@doerken.de.

    Contact form

    You can also use our contact form to send us your request.

    International contact

    Here you will find all the contact details of our international DÖRKEN Membranes subsidiaries and importers.